
Every tool in this series gets the same question. Does spending more actually make you sew better, sew faster, or just enjoy it more? Some tools have earned their price with me. Others turned out to be the same lump of metal in a nicer package. This week it is the bias tape maker, the little tapered cone you feed a fabric strip into at one end and chase with a hot iron at the other.
We have already put that question to sewing scissors, wonder clips, sewing pins, cutting mats and tape measures. This one is worth arguing about, because it is one of the very few sewing tools with no moving parts at all.
What A Bias Tape Maker Actually Does
It is a funnel with a shape. The wide end takes your flat bias strip, the channel inside folds both raw edges in toward the centre as you pull, and single fold tape comes out the narrow end. Nothing powers it: you pull, the iron sets the creases.

Snip the leading end at an angle, then use a pin or bodkin through the slot on top to coax the first inch out the far side. Pin that end to your ironing board. Pull slowly with one hand, press just behind the tool with the other, and never drag the iron along the tape or you will stretch it out of shape.
It only behaves if the strips are cut on the true bias. That diagonal grain lets the tape curve around a neckline instead of buckling.

Size Matters More Than Brand
This is where most first attempts go wrong. The number on a bias tape maker is the width of the finished single fold tape, not the width of the strip you feed in. Clover’s own guidance is to cut on the bias at twice the finished size you want. So a 25mm maker, the one sold as 1 inch, wants a 50mm strip, which is 2 inches. A 12mm maker wants 24mm. Be out by a quarter of an inch and nothing you do at the iron will rescue it.

Fold that 1 inch tape in half once more and you have half inch double fold binding, the width most of my patterns call for. Clover makes the standard tool in 6mm, 12mm, 18mm, 25mm and 50mm.
The Budget Versus Quality Verdict
The budget option is a multi size set of plain metal cones, four or five to a pack. Madam Sew’s four size set, one I checked, covers a quarter inch through to 1 inch. A single branded Clover in 1 inch sits at the cheap end of the notions wall, described on Clover’s own American site as a polymethyl pentane body with iron, which in plain English is a plastic slider riding on a metal channel.
What separates them is how cleanly that channel is finished and how honest the stated size is. No bearings, no blade, nothing to go blunt. A rough channel snags. A channel that is slightly off gives you tape that wanders in width. In fairness, even the good ones wander a little. Sew4Home’s review of the notion says the width varies slightly whichever tool you use.
I went hunting for proof that a hot iron warps the budget cones, and I could not turn up anything I would repeat to you as fact. The bodies are metal, and metal does not slump at pressing temperatures. The real heat problem is your fingers, because the tool sits right under the iron. That is what the plastic slider on the branded one is for. With an all metal set I pull using the tip of a bodkin instead of my thumb.
My verdict: buy the budget set first. Size, not brand, decides whether this tool is any use to you. Once you know the one size you reach for every time, spend a few dollars on that single Clover. If a cheap channel snags your fabric, retire it rather than fight it.
The Two I Would Buy
Two tools, and I would not add a third. The one inch Clover is the one that stays on my ironing board, because that width folds down to the half inch double fold binding most of my patterns ask for. The cheap multi size set earns its place first, though, because it is what tells you which size you actually reach for.
When To Think About A Bias Tape Machine
The hand tool is not slow. The ironing is slow. Three yards of binding is a pleasant ten minutes. Forty yards for a guild quilt is an afternoon and a sore shoulder, and that is where sewists start eyeing the electric bias tape machines. Simplicity’s was the well known one, with interchangeable tips, a temperature dial and a claim of twelve feet a minute. Be warned before you go hunting, though. The sewists who own one report that Simplicity stopped making it, so you are mostly shopping secondhand.
What I would do first costs nothing. Most of the pain is not the folding, it is joining dozens of separate strips end to end. Cut one square of fabric into a single long spiral and all that joining disappears. That is what my continuous bias binding tutorial walks you through, and it is the natural partner to whichever bias tape maker you buy.
The same budget question applies to the blade you cut those strips with.
How Do You Use Your Bias Tape Maker?
Are you a one size sewist or a whole set sewist? Do you keep a single 1 inch Clover and ignore the rest, or does the little 6mm come out for doll clothes and baby bibs? Has anybody talked a badly behaved cheap one into working properly? Tell me in the comments. More small verdicts like this one are gathered in Sewing Tips and Tricks.
Some links above are Amazon affiliate links. As an Amazon Associate, So Sew Easy earns from qualifying purchases at no cost to you.
Some links on this page are affiliate links. As an Amazon Associate, So Sew Easy earns from qualifying purchases, at no extra cost to you.
Thanks so much for your comment!
It would be great if you could share this post with your friends!