<\/noscript><\/figure><\/div>\n\n\nSupplies needed:<\/strong><\/p>\n\n\n\n\nSaral Transfer paper <\/li>\n\n\n\n Marking tool such as a\u00a0tracing wheel <\/li>\n<\/ul>\n\n\n\nThe transfer paper is the key here. It comes in white, red, blue, grey and yellow and is like a sheet of chalked paper, on a roll.<\/p>\n\n\n\n
You can use it to trace your pattern onto your fabric, or use it to trace pattern markings. I like to use it to save time when sewing. I don't even need to cut the pattern out accurately. Place it on top of the fabric with the tracing paper underneath, use the tracing wheel and draw the pattern right onto the fabric to cut out. Very quick, easy and accurate. I use a double tracing wheel that marks my seam allowance on at the same time – genius! Keeps your original pattern intact – anyway, I digress.<\/p>\n\n\n\n
This is what it looks like new, and next to it, a sheet that has been well used, but still works just fine.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\nPlace your fabric wrong side up, place the transfer paper over the top, chalky side facing the fabric and then place the pattern on top.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\nMake sure to accurately place the pattern over the fabric piece and then use the tracing wheel over the dart lines to transfer those lines to the fabric. Easy, quick and accurate.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\nIf you have two pieces that are the reverse of each other, such as two back pieces in a dress, place another sheet of the transfer paper underneath the bottom piece of fabric and you'll be able to mark both at once! Sorted \ud83d\ude42<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\n\nCAUTION – I've never had a problem, but do make sure to test your fabric with the transfer paper to make sure the mark will wash out OK. Always mark on the reverse of your fabric just in case.<\/p>\n<\/blockquote>\n\n\n\n
How to sew double ended darts<\/h2>\n\n\n\n Now your darts are accurately marked in place, it's time to sew. Sewing is just like a regular dart, except we'll do it twice. We fold our dart between the points and pin, making sure the pin pierces the marked dart lines on both sides of the fabric.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\n\nTIP – make sure your pins go into the fabric with their points towards the center on both sides, to make them easier to remove as you sew. If you prefer, put them perpendicular to your sewing direction.<\/p>\n<\/blockquote>\n\n\n\n
Then start somewhere at the center and sew towards the tip of the dart, removing pins as you go. You might want to switch to a shorter stitch length for the last few stitches at the point and then run off the fabric without back stitching. Leave long thread tails and tie off the thread.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\nNow turn the dart around the other way, sew again from the center, overlapping the stitches from the first sewing, and run off the other tip. Tie your threads.<\/p>\n\n\n\n
Pressing your darts<\/h2>\n\n\n\n You can start by pressing your dart flat as sewn. The dart is there to give us shaping at the waist and needs to be flexible.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\nIf you snip through the center of the dart, close to the stitching, you now have that movement and flexibility and can now press your dart to the side and it will lie flat while still allowing the fabric to shape to your body.<\/p>\n\n\n
\n
<\/noscript><\/figure><\/div>\n\n\n \n\n\n